联系我们
公司名称：XXX
电话：XXX
手机：XXX
联系人：XXX
地址：XXX
新闻动态
照明配电箱的电气布线技术应美观、实用
照明配电箱的电气布线技术应美观、实用、施工、操作方便，便于后期维护和检查。配线应兼顾大局，力求整齐划一，和谐大方，以人为本，不落俗套，独立自主，避免给人以混乱感。以下是一些需要注意的要点:
The electrical wiring technology of lighting distribution box shall be beautiful, practical, convenient for construction and operation, and convenient for later maintenance and inspection. Wiring should take into account the overall situation, strive to be neat and uniform, harmonious and generous, people-oriented, unconventional, independent and avoid giving people a sense of confusion. Here are some important points to note:
1. 电缆排列
1. Cable arrangement
1. 电缆敷设结构合理，曲率一致，松紧适中。严禁扭曲、交叉、无序。
1. The cable laying structure is reasonable, the curvature is consistent, and the tightness is moderate. Distortion, crossing and disorder are strictly prohibited.
2. 电缆应由绑扎线或尼龙扎带固定。扎带规格应与电缆的厚度要求一致，规格应一致。
2. The cable shall be fixed by binding wire or nylon strap. The specification of the cable tie shall be consistent with the thickness requirements of the cable, and the specification shall be consistent.
电缆生产结束
End of cable production
1、电缆应小心从事剥线，强度适中，严禁损伤绝缘的电线芯。2.2电缆端采用塑料胶带和黑色塑料绝缘胶带。
1. The cable shall be carefully stripped with moderate strength, and it is strictly prohibited to damage the insulated wire core. 2.2 plastic tape and black plastic insulating tape shall be used at the cable end.
2. 成型后，用红色塑料带包裹头部，用黑色塑料带密封。
2. After forming, wrap the head with red plastic tape and seal it with black plastic tape.
3.在做头部时，塑料带应对折并张紧。绕线时应靠近芯线与护套的连接处。
3. When making the head, the plastic belt should be folded and tensioned. The winding shall be close to the connection between core wire and sheath.
4. 电缆头长度约为26mm，外径不超过电缆护套外径的2mm。电缆头在护套上的绑扎长度一般为13mm左右。
4. The length of cable head is about 26mm, and the outer diameter shall not exceed 2mm of the outer diameter of cable sheath. The binding length of the cable head on the sheath is generally about 13mm.
56. 捆扎电缆后，电缆头应保持在同一高度。2.7电缆的屏蔽层、带、芯应可靠地向外敷设接地。
56. After cable binding, the cable head shall be kept at the same height. 2.7 the shielding layer, belt and core of the cable shall be reliably grounded.
3.电缆标识
3. Cable identification
1. 电缆标识由微机打印制作，包括电缆型号、规格、用途和方向。
1. Cable identification shall be printed and made by microcomputer, including cable model, specification, purpose and direction.
2. 标签应安装防腐蚀、防霉绳，并采用化纤。
2. The label shall be installed with anti-corrosion and anti mildew rope and chemical fiber.
The electrical wiring technology of lighting distribution box shall be beautiful, practical, convenient for construction and operation, and convenient for later maintenance and inspection. Wiring should take into account the overall situation, strive to be neat and uniform, harmonious and generous, people-oriented, unconventional, independent and avoid giving people a sense of confusion. Here are some important points to note:
1. 电缆排列
1. Cable arrangement
1. 电缆敷设结构合理，曲率一致，松紧适中。严禁扭曲、交叉、无序。
1. The cable laying structure is reasonable, the curvature is consistent, and the tightness is moderate. Distortion, crossing and disorder are strictly prohibited.
2. 电缆应由绑扎线或尼龙扎带固定。扎带规格应与电缆的厚度要求一致，规格应一致。
2. The cable shall be fixed by binding wire or nylon strap. The specification of the cable tie shall be consistent with the thickness requirements of the cable, and the specification shall be consistent.
电缆生产结束
End of cable production
1、电缆应小心从事剥线，强度适中，严禁损伤绝缘的电线芯。2.2电缆端采用塑料胶带和黑色塑料绝缘胶带。
1. The cable shall be carefully stripped with moderate strength, and it is strictly prohibited to damage the insulated wire core. 2.2 plastic tape and black plastic insulating tape shall be used at the cable end.
2. 成型后，用红色塑料带包裹头部，用黑色塑料带密封。
2. After forming, wrap the head with red plastic tape and seal it with black plastic tape.
3.在做头部时，塑料带应对折并张紧。绕线时应靠近芯线与护套的连接处。
3. When making the head, the plastic belt should be folded and tensioned. The winding shall be close to the connection between core wire and sheath.
4. 电缆头长度约为26mm，外径不超过电缆护套外径的2mm。电缆头在护套上的绑扎长度一般为13mm左右。
4. The length of cable head is about 26mm, and the outer diameter shall not exceed 2mm of the outer diameter of cable sheath. The binding length of the cable head on the sheath is generally about 13mm.
56. 捆扎电缆后，电缆头应保持在同一高度。2.7电缆的屏蔽层、带、芯应可靠地向外敷设接地。
56. After cable binding, the cable head shall be kept at the same height. 2.7 the shielding layer, belt and core of the cable shall be reliably grounded.
3.电缆标识
3. Cable identification
1. 电缆标识由微机打印制作，包括电缆型号、规格、用途和方向。
1. Cable identification shall be printed and made by microcomputer, including cable model, specification, purpose and direction.
2. 标签应安装防腐蚀、防霉绳，并采用化纤。
2. The label shall be installed with anti-corrosion and anti mildew rope and chemical fiber.
